Union Community VIRDI 3000 Especificaciones Pagina 81
- Pagina / 119
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AC6000
TM
Configuration Manual 81
UNION COMMUNITY Co., Ltd. 44-3 Hyundai Topics Building, Bangi-dong,
Songpa-gu, Seoul, Korea 138-050, Tel: 82-2-6488-3000, Fax: 82-2-6488-3099,
E-Mail:[email protected], http://www.virditech.com
The inputs accept a relay input either Normally Closed or Normally Open. You should program the
input according to your relay activation type. (NC or NO). It is recommended that not more than
one of the same option is used. For example do not program M0 for Door Monitoring and M1 for
Door Monitoring.
These are the available types of monitoring options:
• Disabled – If you do not use the input for anything select this options
• Door Monitor (NC/NO) – if you are connecting a door monitoring device select this option.
The terminal will monitor when the door is opened and closed.
• Lock Monitor (NC/NO) – if you are connecting a lock that can be monitored when the lock
is opened select this option. (Normally used for Motor Lock Monitoring when lock is
opening)
• Lock Monitor 2 (NC/NO) – if you have more than one lock monitoring output on your lock
you can select this option to monitor when the lock is closing. (Normally used for Motor
Lock Monitoring when the lock is closing)
• Inside Open (NC/NO) – if you would like to connect a Request to Exit device, door open
button select this option. Usually if the terminal is on the outside of the door, this door
open button or Request to Exit is connected inside the door. The button is pressed the
terminal will unlock the door.
• Zone 1 InCnt (NC/NO) – This option is used when the terminal is set for people count
application and you are connecting an external device that can be monitored for people
entering or leaving the sensor monitoring area. This is for the In Counting of Zone 1.
• Zone 1 OutCnt (NC/NO) - This option is used when the terminal is set for people count
application and you are connecting an external device that can be monitored for people
entering or leaving the sensor monitoring area. This is for the Out Counting of Zone 1.
• Zone 2 InCnt (NC/NO) - This option is used when the terminal is set for people count
application and you are connecting an external device that can be monitored for people
entering or leaving the sensor monitoring area. This is for the In Counting or Zone 2.
• Zone 2 Out Cnt (NC/NO) - This option is used when the terminal is set for people count
application and you are connecting an external device that can be monitored for people
entering or leaving the sensor monitoring area. This is for the Out Counting of Zone 2.
• Host (NC/NO) – This option is used to disable the terminal from access. In applications
where you have an external controller or terminal that should be accessed first before the
AC6000 you can use this option. If input is not activated, the terminal will not accept
card/fingerprint or id input; when the signal from the external device is de-activated the
terminal will allow access. This can be used in situations where the guard terminal is the
master terminal, when the guard approves the access, then the output will trigger the
AC6000 to allow authentication.
• Fire Monitor (NC/NO) – If you have an external device that has a fire output, the terminal
will monitor when the device detects a fire alarm. The AC6000 will show a fire icon and
give an audible warning tone; if any doors are connected to the terminal the AC6000 will
open the doors. When this signal is activated, UNIS software will also be notified of the
fire signal to alert other terminals connected on the network.
• Security Mode (NC/NO) – You can use this input when you have an external device that
can send a signal when the security system is armed or disarmed. This works in
conjunction with the Lock Output setting of Security Mode. The AC6000 will notify to
arm/disarm the security system; the security system will signal the AC6000 that is was
armed/disarmed.
- Configuration Manual 1
- 2 2
- 3 3
- < Glossary> 4
- Table of Contents 5
- 12 12
- 1. Before use 13
- 15
- 2. Introduction 24
- 25 25
- 26 26
- 2.2. Configuration 27
- 2.2.1. Network configuration 27
- 28 28
- 30 30
- Operation Icon Description 31
- 3.2.3.1.1. Duress User 36
- 3.2.3.3. Deleting a User 45
- 3.2.3.4. Modifying a User 46
- 3.2.3.5. Viewing Users 47
- 3.2.4. Network Settings 49
- 3.2.4.1. Terminal ID Number 49
- Wireless 51
- Options 51
- 3.2.5.3. Meal Application 57
- 3.2.5.4. Shift Management 59
- 3.2.5.5. People Count 60
- In some 62
- 63 63
- 3.2.6. System Settings 64
- 3.2.6.1. System Settings 65
- 3.2.6.1.1. User ID Length 65
- 3.2.6.2.1. 1:N Level 67
- 3.2.6.2.2. 1:1 Level 67
- 3.2.6.3.1. Display Format 68
- 3.2.6.3.2. Set Current Date 69
- 3.2.6.3.3. Set Current Time 70
- 3.2.6.4. Database Options 70
- 3.2.6.4.2. Delete All Users 71
- 3.2.6.4.3. Clear Settings 71
- 3.2.6.4.4. Clear Log Data 71
- 3.2.6.4.6. Delete All 71
- 3.2.6.5.1. User Group ID 72
- 3.2.6.5.3. 1:N Matching 73
- 3.2.6.5.4. Card Only 73
- 3.2.6.5.5. Template On Card 73
- 3.2.6.5.6. Job Code 73
- 3.2.6.6. Face Detection 74
- 3.2.6.6.1.1. Detection Level 74
- 3.2.7.1. Sound Settings 76
- 3.2.7.1.1. Voice Volume 76
- 3.2.7.1.2. Sound Volume 76
- 3.2.7.2. Wiegand Settings 77
- 3.2.7.2.1. Site Code 78
- 3.2.7.2.2. Format 78
- 3.2.7.3.3. Card Reader 80
- 3.2.7.4. Input Settings 80
- 3.2.7.5. Lock Settings 82
- 3.2.7.6. External Options 83
- 3.2.7.6.1. Printer Option 83
- 3.2.7.6.1.1. RS485 Option 84
- 3.2.8.1.2. Arrange Icons 86
- 3.2.8.1.3. Main Background 87
- Camera Settings 88
- 3.2.8.3. Language 90
- 3.2.8.4. LCD Options 90
- 3.2.8.4.1. Screen Saver 91
- 3.2.9.4. User Information 94
- 3.2.9.6. About 96
- 3.2.10. USB Options 97
- 3.2.10.1. Database Export 98
- 3.2.10.2. Database Import 99
- 3.2.10.3. Firmware Upgrading 99
- 4.3.1. Font Importing 101
- 4.5. Customizing Sounds 102
- 5. How to use the terminal 103
- 5.2. ID Entry Screen 105
- 5.4. Job Code Authentication 108
- 6. Application Modes 109
- 6.3. Cafeteria Application 111
- 6.6. Security Mode 114
- Arm/disarm 115
- 7. Firmware Upgrading 116
- 7.1. Upgrading from USB 117
- 7.2. Upgrading from UNIS 117
- 8. Troubleshooting Guide 118
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Union Community VIRDI 3000
(59 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales